新闻资讯

New center

Check category
/
/
/
Die casting processing in china

Die casting processing in china

  • Categories:Industry news
  • Author:
  • Origin:
  • Time of issue:2022-07-12 08:23
  • Views:

(Summary description)The entrance of the runner of the cold horizontal mold should generally be located at more than 2/3 of the inner diameter of the upper part of the pressure chamber, so as to prevent the molten metal in the pressure chamber from entering the runner prematurely under the action of gravity and starting to solidify in advance.

Die casting processing in china

(Summary description)The entrance of the runner of the cold horizontal mold should generally be located at more than 2/3 of the inner diameter of the upper part of the pressure chamber, so as to prevent the molten metal in the pressure chamber from entering the runner prematurely under the action of gravity and starting to solidify in advance.

  • Categories:Industry news
  • Author:
  • Origin:
  • Time of issue:2022-07-12 08:23
  • Views:

How much do you know about the required knowledge of die casting molds? Let's follow the editor of Die casting processing in china for a brief understanding!
1. The entrance of the runner of the cold horizontal mold should generally be located at more than 2/3 of the inner diameter of the upper part of the pressure chamber, so as to prevent the molten metal in the pressure chamber from entering the runner prematurely under the action of gravity and starting to solidify in advance.
2. The cross-sectional area of ??the runner should gradually decrease from the sprue to the inner gate. If the cross-section is enlarged, negative pressure will appear when the molten metal flows through, and it is easy to inhale the gas on the parting surface and increase the molten metal. The eddies in the flow envelop the air. Generally, the section at the outlet is 10-30% smaller than that at the inlet.

Die casting processing in china
3. The runner should have a certain length and depth. The purpose of maintaining a certain length is to stabilize the flow and guide. If the depth is not enough, the molten metal will cool down quickly, and if the depth is too deep, the condensation will be too slow, which will not only affect the productivity but also increase the amount of return material.
4. The cross-sectional area of ??the runner should be larger than the cross-sectional area of ??the inner gate to ensure the speed of the molten metal entering the mold. The cross-sectional area of ??the main runner should be larger than that of each branch runner.
5. The two sides of the bottom of the runner should be rounded to avoid early cracks, and the two sides can be inclined at about 5°.
The above is what Die casting processing in china tells: a brief introduction to the required knowledge of die casting molds.

Keyword:

推荐新闻

Ingate knowledge of Die casting processing in china
Ingate knowledge of Die casting processing in china
Time of issue : 2022-07-19 08:26:56
After the molten metal enters the mold, the parting surface should not be closed immediately, and the overflow groove and the exhaust groove should not directly impact the mold core. The flow direction of the molten metal after entering the mold is as far as possible along the cast ribs and heat sinks, filling from the thick wall to the thin wall, etc.
See more information
After the molten metal enters the mold, the parting surface should not be closed immediately, and the overflow groove and the exhaust groove should not directly impact the mold core. The flow direction of the molten metal after entering the mold is as far as possible along the cast ribs and heat sinks, filling from the thick wall to the thin wall, etc.
Die casting processing in china
Die casting processing in china
Time of issue : 2022-07-12 08:23:16
The entrance of the runner of the cold horizontal mold should generally be located at more than 2/3 of the inner diameter of the upper part of the pressure chamber, so as to prevent the molten metal in the pressure chamber from entering the runner prematurely under the action of gravity and starting to solidify in advance.
See more information
The entrance of the runner of the cold horizontal mold should generally be located at more than 2/3 of the inner diameter of the upper part of the pressure chamber, so as to prevent the molten metal in the pressure chamber from entering the runner prematurely under the action of gravity and starting to solidify in advance.
Advantages of Die casting processing manufacturers
Advantages of Die casting processing manufacturers
Time of issue : 2022-07-05 08:37:55
The advantages of Die casting processing manufacturers include excellent dimensional accuracy of castings. Usually this depends on the casting material, typical values are 0.1mm error at the first 2.5cm size and 0.002mm error for every 1cm increase.
See more information
The advantages of Die casting processing manufacturers include excellent dimensional accuracy of castings. Usually this depends on the casting material, typical values are 0.1mm error at the first 2.5cm size and 0.002mm error for every 1cm increase.
Previous page
1
2
10

Foshan Nanhai Jiawei metal products Co., Ltd

Contact information:18928682636(Miss Liang)/18928682621(Mr. Tang)

Company phone:0757-85103282

Company fax:0757-85103183

Company email:sunny@nhjiawei.com / jia_tangvic@163.com

Marketing Center: No.90, hongganglihe Road, Lishui Town, Nanhai District, Foshan City

Production base: b3-1, zone 3, Enping Industrial Park, Jiangmen industrial transfer park (Enping Guangen profile Co., Ltd.)

language
中国
韩国
韩国
韩国
韩国
韩国
Copyright ? 2021 Foshan Nanhai Jiawei metal products Co., Ltd 粤ICP备19125561号 Powerby :300.cn 
XML 地图 | Sitemap 地图